Support

Install
How to install your Pinlock® lens
How_to_install_your_pinlock_lens.mp4
Install your Pinlock® lens
/sites/default/files/2023-04/Pinlock_Warranty_Lens_1920x1080_v1.pdf
/sites/default/files/2023-07/Pinlock_Instruction_Manual_Lens_Installation.pdf
Adjust
How to adjust your Pinlock® lens
How_to_adjust_pinlock_one_component_pin.mp4
Adjust your One Component Pin
/sites/default/files/2023-07/Pinlock_Instruction_Manual_Lens_Adjustment_One_Component_Pin_1.pdf
How_to_adjust_pinlock_three_component_pins.mp4
Adjust your Three Component Pin
/sites/default/files/2023-07/Pinlock_Instruction_Manual_Lens_Adjustment_Three_Component_Pin_1.pdf
How_to_adjust_pinlock_tear-off_pins.mp4
Adjust your Tear-Off Pin
/sites/default/files/2023-07/Pinlock_Instruction_Manual_Lens_Adjustment_Tear-off_Pin_0.pdf
Clean
How to clean your Pinlock® lens
How_to_use_pinlock_visor_clear.mp4
Clean your Pinlock® lens
/sites/default/files/2023-07/Pinlock_Instruction_Manual_Lens_Maintenance.pdf
FAQ

Everything you need to know about our products

Can’t find the answer you’re looking for? Please drop us an email at info@pinlock.com.

Lenses

How to install your Pinlock lens

  1. Remove the helmet visor from the helmet.
  2. Check if the arrows on the Pinlock® pins in the visor are pointing outwards.
  3. Flex the helmet visor and place the Pinlock® lens between the two pins.
  4. Check with natural light if the silicon seal on the Pinlock lens makes full contact with the helmet visor.
  5. Remove the protective film from the Pinlock lens.
  6. Fit the helmet visor back on the helmet.

For a detailed instruction check the video or download the instruction manual.

How to clean your Pinlock lens

  1. Remove the helmet visor from the helmet.
  2. Flex the helmet visor delicately until there is no more tension on the Pinlock lens. Carefully remove the Pinlock lens from its position, avoid touching the lens surface.
  3. Softly remove all dirt with a dry microfiber cloth. Only clean the Pinlock lens and the helmet visor using lukewarm water and a soft microfiber cloth.
  4. Allow the Pinlock lens and the helmet visor to dry naturally before reassembling them.
  5. Flex the helmet visor and place the Pinlock lens between the two pins.
  6. Check with natural light if the silicon seal on the Pinlock lens makes full contact with the helmet visor.
  7. Fit the helmet visor back on the helmet.

Pins

Adjust your One Component Pin

  1. Please remove the Pinlock® lens from the visor before adjusting the Pinlock® One Component Pin.
  2. Adjust the pins by pushing them outwards and turning them with your fingers before pushing them back in. Use steps of maximum 45° degree tension build up.
  3. When the silicone seal of the Pinlock lens makes a full seal all around the lens and the visor, the adjustment is complete.

Does your lens not make a full seal with your pins at maximum tension? Feel free to contact us at info@pinlock.com.

Adjust your Two Component Pin

  1. Please remove the Pinlock® lens before adjusting the Pinlock® Two Component Pin.
  2. You can adjust the position of the pin with a flathead screwdriver or bank card. Use steps of maximum 45° degree tension build up.
  3. When the silicone seal of the Pinlock lens makes a full seal all around the lens and the visor, the adjustment is complete.

Does your lens not make a full seal with your pins at maximum tension? Feel free to contact us at info@pinlock.com.

Adjust your Three Component Pin

  1. Please remove the Pinlock® lens before adjusting the Pinlock® Three Component Pin.
  2. Adjust the tension of the Pinlock lens by turning the hexagon on the inside of the visor using a 5 mm hexagon tool. Use steps of maximum 45° degree tension build up.
  3. When the silicone seal of the Pinlock lens makes a full seal all around the lens and the visor, the adjustment is complete.

Does your lens not make a full seal with your pins at maximum tension? Feel free to contact us at info@pinlock.com.

Adjust your Tear-off Pin

  1. Please remove the Pinlock® lens before adjusting the Pinlock® Tear-off Pin.
  2. Adjust the tension of the Pinlock lens by turning the hexagon on the inside of the visor using a 5 mm hexagon tool. Use steps of maximum 45° degree tension build up.
  3. When the silicone bead of the Pinlock lens makes a full seal all around the lens and the visor, the adjustment is complete.

Does your lens not make a full seal with your pins at maximum tension? Feel free to contact us at info@pinlock.com.